35 Pounds with 20,000 BTUS of safe heat. The Firebird Compact 20 is a powerful, portable, & safe heater providing instant heat exactly where you need it.
Phoenix Firebird Electric Heater Drying System
The Firebird portable, heavy duty electric heater features a built-in 50-amp twist lock receptacle designed to work with standard 30 or 50 amp power sources—select the setting using the HIGH/LOW switch.
At the 50-amp setting, the Firebird produces 31,000 BTU’s—that’s 360 CFM with a 80°F temperature rise. In an area with below freezing temperatures the Firebird can produce 360 CFM of air over 100 degrees. Using the 30-amp setting the Firebird produces 18,000 BTU’s—giving a 46°F temperature rise. Internal temperature cutouts prevent the Firebird from overheating an area, while the Firebird’s included remote thermostat provides a means to control the heat from anywhere in the drying space.
Phoenix FireBird – Portable Heater Rental!
Call Today!
1-800-506-6048
Flood Cleanup Water Damage Repair in Markham, How to deal with Flood Damage?, Mold Inspection, Testing & Removal Mississauga, Frozen pipe & how to prevent them?, Ottawa Air Duct Cleaning, Toronto Air Duct Cleaning, Air Duct Cleaning Montreal,
get a quote now
Key Features
-
- Listed by ETL to UL Safety Standards, NEC Compliant:
- 30 or 50 Amp operation (18,000 BTU/31,000 BTU):
- 30 Amp = 24 Actual Amp Draw and 46ºF Temperature Rise 50 Amp = 40 Actual Amp Draw and 80ºF Temperature Rise:
- Two 8’ Power Cords (1 dryer, 1 range) included with unit:
- Remote Thermostat (with 25’ connecting wire) included with unit:
- Multiple air filter options Standard MERV-11, MERV-14:
- Multiple ducting options 12” intake, 12” supply:
- Detachable 12” Duct Collar stores in lid with room for power cords:
- Stainless steel cabinet:
Technicians Review
1 Specifications
Part No. 4027300
Power User selectable 30/50 A operation 220/240 VAC
30 Amp = 46°F temperature rise; 18,000 BTUs
50 Amp = 80°F temperature rise; 31,000 BTUs
Blower 360 CFM
Filters Pleated Media MERV-11 Duct Options Intake – 12” Flex-Duct
2 Operation
2.1 Transporting
The Phoenix FireBIRD must always be upright when transported by vehicle. It may be tipped onto its handle and back for loading and moving by hand. The Phoenix FireBIRD features a high-impact plastic skid plate which protects the unit while navigating obstacles such as curbs, stairways, and while loading into vehicles.
2.2 Electrical Requirements
The Phoenix FireBIRD requires 220/240VAC. The FireBIRD outlet is 240VAC with ground. When properly installed,
it provides a ground connection through the cord to the heater to protect the operator from electric shock. The Phoenix FireBIRD comes equipped with two 8’ long cords for connection to grounded residential range and dryer receptacles. An accessory extension cord is also available (see Accessories).
2.3 Ducting
The Phoenix FireBIRD can be ducted at the inlet, the outlet or both using the included round outlet adapter. The FireBIRD lid and outlet adapter are designed to accommodate 12” flexible duct. When selecting flexible ducting keep in mind anticipated outlet temperatures. Air temperature increase is typically 50 to 80 degrees F for low and high power settings respectively. Adding ducting
decreases airflow which can increase outlet temperatures by up to 20 additional degrees F.
Install the 12” duct adapter by lining up the notch of the adapter with the rivet on the cabinet, then push in the directions shown to engage fasteners.
Master POWER Switch: The master power switch located on the back of the FireBIRD can be used to turn the unit ON, OFF, or set the unit to be controlled by an external thermostat.
When set to ON, the FireBIRD will energize the blower relay and heater elements(s) continuously. In this mode, the heaters are thermostatically limited to 140 degree F incoming air temperature with an automatic switch.
When set to THERMOSTAT, the blower and heater will run when the thermostat terminals (located under the lid) are connected by a switch, remote thermostat, timer, etc.
HIGH/LOW POWER Switch: This switch selects either high or low power operation. If this switch is set to HIGH POWER operation, the FireBIRD MUST be connected to a minimum 50 Amp source.
2.5 Hour Meter
The digital hour meter measures the cumulative time that the unit is turned on to tenths of an hour. It stores and displays the total when the unit is unplugged. It resets to zero after 99,999.9 hours of operation.
2.6 Remote Thermostat Connection
To connect the included remote thermostat, first locate the thermostat terminals under the lid of the FireBIRD. There are 2 spring loaded terminals for connecting the thermostat wiring. Connect one wire to each terminal. If the FireBIRD is placed inside the space to be heated, place the thermostat on top of the unit. For applications where the FireBIRD is placed outside the space to be heated (e.g. ducting heat into a chamber), the 25’ cord allows you to place the thermostat inside the heated space.
In addition to the included thermostat, any dry-contact switch or other type of control that connects the terminals together will cause the heater to run. The thermostat circuit is low voltage (24VAC). DO NOT CONNECT POWER TO THE
THERMOSTAT TERMINALS. Always press terminal levers to release spring pressure before disconnecting thermostat wiring. Failure to do so will lead to excessive wear on spring loaded terminal connector.
